客服QQ:

675609587

郵箱地址:

675609587@qq.com

電話:13280489678

手機:13280489678

> 新聞中心 > 技術資料 >

搖臂鉆床操作技巧,快速上手操作的辦法

2020-09-02 21:29來源:未知瀏覽:

搖臂鉆床操作技巧,快速上手操作的辦法

 

更好的操作搖臂鉆床技巧:

 

1、搖臂鉆床工件裝夾必須牢固可靠。鉆削小工件時,應用工具夾持,不準用手拿著鉆。工作中嚴禁戴手套。

2、使用自動走刀時,要選好進給速度,調整好行程限位塊。手動進刀時,逐漸增加壓力或逐漸減小壓力,以免用力過猛造成事故。

3、搖臂鉆床鉆頭上纏有長鐵屑時,要停車清理,用刷子或鐵鉤清除,嚴禁用手拉。

4、精絞深孔、拔錐棒時,不可用力過猛,以免手撞在刀具上。

5、工件材料較硬或鉆孔較深時,應在工作過程中不斷將鉆頭抽出孔外,排除鉆屑,防止鉆頭過熱并使用冷卻潤滑液。必要時采用保護性卡頭。

6、鉆孔時,身體不要離主軸太近,以免頭發或衣服被鉆頭卷入。

7、用鉆床絞孔時,絕對不可倒轉,否則鉸刀和孔壁之間容易擠住刀屑,造成孔壁劃傷或刀刃崩裂。

8、使用搖臂鉆床搖臂鉆時,橫臂回轉范圍內不準站人,不準有障礙物。工作時橫臂必須夾緊。

9、搖臂鉆床橫臂及工作臺上不準堆放物件。

10、工件結束時,將橫臂降到最低位置,主軸箱靠近主軸,并且要夾緊。

 

 

Better operation skills of radial drilling machine:

1. The rocker arm of the drill must be fixed firmly and reliably. When drilling small workpieces, it should be clamped with tools. It is not allowed to hold the drill by hand. Do not wear gloves during work.

2. When using the automatic feed, the feed speed should be selected and the travel limit block should be adjusted. When manually feeding, gradually increase or decrease the pressure to avoid accidents caused by excessive force.

3. When long iron chips are wrapped on the drill bit of radial drilling machine, stop the machine for cleaning, and use brush or iron hook to remove it. It is strictly forbidden to pull it by hand.

4. Do not use too much force when reaming deep hole and pulling taper rod, so as to avoid hitting the tool by hand.

5. When the workpiece material is hard or the drilling is deep, the drill bit should be continuously pulled out of the hole during the working process to remove the drilling cuttings, prevent the drill bit from overheating and use cooling lubricant. If necessary, use protective clamps.

6. When drilling, the body should not be too close to the main shaft, so as to avoid the hair or clothes being involved by the drill bit.

7. When reaming a hole with a drilling machine, it is absolutely not allowed to turn it upside down, otherwise the cuttings will be squeezed between the reamer and the hole wall, resulting in the scratch of the hole wall or the crack of the blade.

8. When the radial drilling machine is used, people are not allowed to stand in the rotating range of the cross arm and there are no obstacles. The cross arm must be clamped during operation.

9. It is not allowed to stack objects on the cross arm and working table of radial drilling machine.

10. At the end of the workpiece, lower the cross arm to the lowest position, and the spindle box is close to the spindle, and should be clamped.

  • 電話:13280489678
  • 聯系人:鄭經理
  • 郵箱:675609587@qq.com
  • 地址:山東省滕州市經濟開發區
  • 山東沈北數控產品有機械搖臂鉆床、液壓搖臂鉆床、立式鉆床、數控鉆床、銑床、鋸床、液壓機等型號機床設備及配件。廠家直接發貨質量保證,價格優惠,發貨周期短,產品暢銷國內及國際市場,得到了越來越多的國內外客戶的認可和支持。

微信二維碼

Copyright © 山東沈北數控機床有限公司 版權所有 備案號:魯ICP備20014639號-3
在线欧美精品一区二区三区,中文字幕精品一区二区精品,色五月丁香五月综合五月亚洲,国产蝌蚪免费精品视频